Audio Technica AT-VM95C
VM95 Series Stereo Conical Capsule
VM95 series AT-VM95C conical stylus stereo cartridge with aluminum cantilever, 4.0 mV output voltage, body compatible with all VM95 series styli and replacement model for AT91, AT91R and CN5625AL.
AT-VM95C, Audio-Technica's new entry-level cone capsule, replaces legendary AT90-series models such as the AT91, AT91R and CN5625AL
In addition, the AT-VM95C is a low cost cartridge incorporating a tapered stylus, and compatibility with the range will allow you to upgrade to any of the other 4 LP styli the series offers such as the Elliptical, Elliptical Bare, Microlinear and Shibata.
aluminum cantilever
4.0mV output voltage
Body compatible with VM95 series needle assemblies
Replacement for AT91, AT91R and CN5625AL
VM95 Series - Stylus Compatibility
Every diamond stylus in a capsule wears after a period of work.
Around 500 hours for a conical stylus, 300 hours for an elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.
Our VM95 series dual moving magnet cartridges can be used virtually forever if the interchangeable stylus is replaced. It is no longer necessary to purchase a full capsule when the diamond tip has been worn down; you just have to purchase the right replacement stylus, but you can also enjoy the experience of upgrading your cartridge with a different stylus.
The six capsule models that make up the V95 series use the same electromagnetic motor body, therefore each of the six replacement needles is perfectly compatible:
AT-VMN95C
AT-VMN95E
AT-VMN95EN
AT-VMN95ML
AT-VMN95SH
AT-VMN95SP
AT-VM9E series compatibility with AT-XP series DJ cartridges
The XP-series electromagnetic body-motor is fully compatible with all VM95-series replacement styli and delivers a higher output voltage than the VM95-series cartridge. This improves compatibility with the phono inputs of professional DJ mixers.
The VM95 series' electromagnetic motor-body is also compatible with the three replacement styli on the AT-XP series DJ cartridges; in any case, the XP-series electromagnetic body-motor will deliver a higher output voltage than the VM95-series cartridge, in order to offer better compatibility with the phono inputs of professional DJ mixers.
Remember that the typical tracking force when using the XP series styli is three grams, instead of two grams for the VM95 series styli.
The XP-series stylus suspension design and compliance has been optimized for heavy use by DJs, including possible hand-picking and back-and-forth movement.
The suspension design and compliance for the VM95 series has been engineered for optimal audiophile playback:
ATN-XP7
ATN-XP5
ATN-XP3
Glued conical needle
The advantage of the conical stylus, even when the cartridge is "tilted", is that the spherical surface of this stylus touches the groove of vinyl records precisely.
Does not use nuts
The VM95 series cartridges feature two M2.6 threaded inserts that allow the cartridge to be installed on the tonearm or a detachable headstock, without the use of nuts. Each capsule includes a pair of 8mm M2.6 screws, a pair of 11mm M2.6 screws, and two plastic washers.
Technical characteristics:
TYPE: Stereo double magnet VM
MOUNTING: 1/2" Center
FREQUENCY RESPONSE: 20 - 20,000 Hz
CHANNEL SEPARATION: 18 dB (1 kHz)
OUTPUT CHANNEL BALANCE: 2.5 dB (1 kHz)
OUTPUT VOLTAGE: 4.0 mV (1 kHz and 5 cm/s)
VERTICAL TRACKING ANGLE: 23°
VERTICAL TRACKING FORCE RANGE: 1.8 - 2.2g (2.0g standard)
NEEDLE SHAPE: Tapered
NEEDLE SIZE: 0.6 mil
NEEDLE CONSTRUCTION: Fixed diamond stylus on rounded shank
CANTILEVER: Aluminum tube
RECOMMENDED LOAD IMPEDANCE: 47,000 Ω
COIL IMPEDANCE: 3.3 kΩ (1 kHz)
COIL INDUCTANCE: 550 mH (1 kHz)
DC RESISTANCE: 485 Ohms
STATIC COMPLIANCE: 17 × 10-6 cm/dyne
DYNAMIC CONFORMITY: 6.5 × 10-6 cm/dyne (100Hz)
RECOMMENDED LOAD CAPACITANCE: 100 - 200 pF
WEIGHT: 6.1g
DIMENSIONS: 17.2 mm (Height) x 18.9 mm (Width) x 28.3 mm (Depth)
SPARE NEEDLE AT-VMN95C
CABLE USED FOR THE COIL: T.P. Copper
ACCESSORIES INCLUDED:
Two 11mm screws for installation
Two 8mm screws for installation
Two washers