AUDIOTECHNICA AT-VM95EN. Moving magnet cartridge (MM) with integrated cartridge holder.
Stereo cartridge with bare elliptical stylus VM95 series.
AT-VM95EN incorporates a bare elliptical stylus. The stylus construction, consisting of a piece of diamond with a round shank inserted into the cantilever, creates a lightweight and more rigid drive system than a diamond tip glued onto a round titanium shank, as is the case with the AT-VM95E. In addition, the use of a bare diamond means a substantial difference in price, although the quality of reproduction will be immediately apparent, specifically in the high-frequency fidelity and quality of transient response.
Aluminium cantilever.
Output voltage of 3.5mV.
Body compatible with all VM95 series needle assemblies.
Frequency response from 20 to 23,000Hz.
VM95 Series - Needle Compatibility.
Every diamond stylus in a capsule is subject to wear after a period of use.
About 500 hours for a conical stylus, 300 hours for an elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.
Nuestras cápsulas de doble imán móvil de la serie VM95 pueden ser utilizadas prácticamente para siempre si se sustituye la aguja intercambiable. Ya no es necesario adquirir una cápsula completa cuando se ha desgastado la punta de diamante; simplemente hay que adquirir la aguja de recambio adecuada, pero también puede disfrutar de la experiencia de actualizar su cápsula con una aguja diferente.
The six capsule models that make up the VM95 series use the same electromagnetic motor body, so each of the six replacement needles is perfectly compatible.
AT-VMN95C
AT-VMN95E
AT-VMN95EN
AT-VMN95ML
AT-VMN95SH
AT-VMN95SP
Compatibility of the AT-VM9E series with the AT-XP series DJ cartridges.
The XP series electromagnetic motor body is fully compatible with all VM95 series replacement styli and delivers a higher output voltage than the VM95 series cartridge. This improves compatibility with the phono inputs of professional DJ mixers.
The VM95 series electromagnetic body-motor is also compatible with the three replacement styli of the AT-XP series DJ cartridges; in either case, the XP series electromagnetic body-motor will deliver a higher output voltage than the VM95 series cartridge, in order to provide better compatibility with the phono inputs of professional DJ mixers.
Remember that the typical tracking force when using XP series needles is three grams, as opposed to two grams for VM95 series needles.
The suspension design and compliance of the XP Series needles has been optimised for heavy use by DJs, including possible manual pinch and backward movement.
The suspension design and compliance for the VM95 series has been designed for optimal audiophile playback.
ATN-XP7
ATN-XP5
ATN-XP3
Bare elliptical stylus.
The elliptical diamond stylus follows the groove modulation more accurately compared to the conical stylus, offering better frequency and phase response while reducing distortion.
No nuts are used.
The VM95 series capsules incorporate two M2.6 threaded inserts, allowing the capsule to be installed on the arm or on a detachable head without the use of nuts. Each cartridge includes one pair of 8 mm M2.6 screws, one pair of 11 mm M2.6 screws and two plastic washers.
Cartridge & Stylus.
Frequency Response 20 - 23,000 Hz.
Channel Separation 22 dB (1 kHz).
Vertical Tracking Angle 23°.
Vertical Tracking Force 1.8 to 2.2g (2.0g standard).
Needle Construction Bare round shank.
Recommended Load Impedance 47.000 Ω.
Coil Impedance 3.3 kΩ (1 kHz).
DC resistance 485 Ω.
Coil Inductance 550 mH (1 kHz).
Output Voltage 3.5 mV (@ 1 kHz, 5 cm/sec).
Output Channel Balance 2.0 dB (1 kHz).
Needle Shape Elliptical.
Cantilever Aluminium tube.
Static Compliance 20 x 10 - 6 cm / dyne.
Dynamic Compliance 7 x 10 - 6 cm / dyne (100 Hz).
Mounting 1/2" between centres.
Capsule Weight 6.1gr.
Dimensions 17.2 x 18.9 x 28.3 (H x W x D in mm).
Accessories Included Two screws 11 mm installation;
Two screws 8 mm installation;
Two washers.
Non-magnetic screwdriver.
Model AT-VM95EN.
Recommended Load Capacitance 100-200 pF.
Replacement Needle AT-VMN95EN.
Needle Size 0.3 x 0.7 mil.
Type VM Stereo double magnet.
Cable Used for T.P. Coil Copper.