Audio Technica AT-VM95ML: Dual Moving Magnet Capsule
VM95 Series Microlinear Stereo Capsule
This VM95 series cartridge with a 2.2 x 0.12 mil Microlinear stylus can be used with half-inch anchor turntables. The capsule provides excellent channel separation and low distortion for impressive tonal quality. The rugged, low-resonance housing features threaded inserts that allow the cartridge to be mounted to the headstock with just two screws, without the need for nuts. And since the entire VM95 series shares the same body, the stylus can be replaced with any of the six interchangeable AT-VMN95 replacement styli.
The AT-VM95ML features a bare Microlinear diamond stylus that will allow you to double the life of your stylus. Linear contact stylus performance will minimize "inner groove distortion" and provide an extended frequency response, maximizing resolution in the mid and high frequencies of audio program material.
VM95 Series Dual Magnet Cartridge with 2.2 x 0.12 Mil Microlinear Stylus
Aluminum cantilever
Low Resonance Rugged Polymer Housing
3.5mV output voltage
Body compatible with all VM95 series needles
Frequency response from 20 to 25,000 Hz
Compatible with any AT-VMN95 replacement needle
Threaded insert in the body of the capsule that allows it to be mounted on the head with only two screws, without the need for nuts
VM95 Series - Stylus Compatibility
Every diamond stylus in a capsule wears out after a period of work.
Around 500 hours for a conical stylus, 300 hours for an elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.
Our VM95 series dual moving magnet cartridges can be used virtually forever if the interchangeable stylus is replaced. It is no longer necessary to purchase a full capsule when the diamond tip has been worn down; you just have to purchase the right replacement stylus, but you can also enjoy the experience of upgrading your cartridge with a different stylus.
All six cartridge models that make up the VM95 series use the same electromagnetic motor body, therefore each of the six replacement styli is perfectly compatible.
AT-VM9E series compatibility with AT-XP series DJ cartridges
The XP-series electromagnetic body-motor is fully compatible with all VM95-series replacement styli and delivers a higher output voltage than the VM95-series cartridge. This improves compatibility with the phono inputs of professional DJ mixers.
The VM95 series' electromagnetic motor-body is also compatible with the three replacement styli on the AT-XP series DJ cartridges; in any case, the XP-series electromagnetic body-motor will deliver a higher output voltage than the VM95-series cartridge, in order to offer better compatibility with the phono inputs of professional DJ mixers.
Remember that the typical tracking force when using the XP series styli is three grams, instead of two grams for the VM95 series styli.
The XP-series stylus suspension design and compliance has been optimized for heavy use by DJs, including possible hand-picking and back-and-forth movement.
The suspension design and compliance for the VM95 series has been engineered for optimal audiophile playback.
Technical characteristics:
TYPE: Stereo double magnet VM
MOUNTING: 1/2" on center
FREQUENCY RESPONSE: 20 - 25,000 Hz
CHANNEL SEPARATION: 23dB (1kHz)
OUTPUT CHANNEL BALANCE: 1.5 dB (1kHz)
OUTPUT VOLTAGE: 3.5 mV (1kHz and 5 cm/s)
VERTICAL TRACKING ANGLE: 23°
VERTICAL TRACKING FORCE RANGE: 1.8 - 2.2g (2.0g standard)
NEEDLE SHAPE: Micro Linear
NEEDLE SIZE: 2.2 x 0.12 mil
NEEDLE CONSTRUCTION: Bare Square Shank
CANTILEVER: Aluminum tube
RECOMMENDED LOAD IMPEDANCE: 47,000 ohms
COIL IMPEDANCE: 3.3 kohms (1 kHz)
COIL INDUCTANCE: 550 mH (1 kHz)
DC RESISTANCE: 485 Ohms
STATIC COMPLIANCE: 20 × 10-6 cm/dyne
DYNAMIC CONFORMITY: 10 × 10-6 cm/dyne (100Hz)
CABLE: T.P. Copper
RECOMMENDED LOAD CAPACITANCE: 100-200 pF
WEIGHT: 6.1g
DIMENSIONS: 17.2 mm (Height) x 18.9 mm (Width) x 28.3 mm (Depth)
SPARE NEEDLE AT-VMN95ML